Two: Initiate An Account On The Exchange Or Broker Platform And Verify It
Once you have chosen either a cryptocurrency exchange or brokerage, you must sign up and open an account with them. Some exchanges and brokerage platforms will require you to verify your identity, so if this is something you dont want to do, you need to find a different place to buy your cryptocurrency. However, its best to participate in this step, as verifying your identification will help prevent fraud and allow you to meet federal regulatory requirements.
Additionally, if you dont complete this verification step, you might not be able to buy cryptocurrency on your exchange or brokerage platform of choice. Usually, to perform the identification process, the exchange or broker will ask you for a drivers license or passport. Some will even want you to upload an image of yourself to ensure it matches the identification you provided.
The Best Cryptocurrencies To Buy For Beginners
If you are a beginner at buying cryptocurrency, you are likely overwhelmed by how many options there are. As of January 2021, there were approximately more than 4,000 cryptocurrencies available for purchase.
This figure is daunting, and researching each one to decide which to invest in could take you quite some time. Thats why we have somewhat narrowed down the list for you by providing the top six cyrptocurrencies you should consider buying if youre a beginner.
- Bitcoin Cash
- Polkadot
Install Flashing In The Roof Valley
We won’t go into roofing details here . In general, cover the eaves and valley with strips of a waterproof membrane and install the sheet metal valley. Place roofing nails about 12 in. apart along the edge of the metal valley. Cut a short piece of valley metal to complete the top on each side, overlapping it about 6 in. onto the long piece.
Staple No. 15 building paper to the remainder of the porch roof, starting at the bottom and working up. Overlap each row 3 in. onto the one below. Install shingles to match the house. Follow the manufacturer’s instructions for starting, overlaps and nail placement. Use 1-in.-long galvanized roofing nails to avoid nailing through the tongue-and-groove ceiling.
You May Like: How To Install A Ceiling Fan On An Existing Aluminum Patio Cover
Install The Support Posts
You can place the columns outside the porch area or install them on the porch deck. In the former case, youll have to dig holes in the ground and fix the support posts into these holes using concrete. In the latter case, you will have to anchor the columns to the beams located under the deck. For the patio, you have to attach the columns to the concrete using special fasteners.
Cut Away The Overhang And Siding To Make Way For The Porch
You’ll have to decide whether to cut a slot where the porch walls meet the siding. If your siding is stucco, brick or stone, you may want to butt the walls to the siding.
Make a mark 1-5/8 in. out from the deck on both sides. Then make another mark 5-1/8 in. inside the first mark. Draw plumb lines up from these marks and cut a 5-1/8-in. slot through the siding but not the sheathing. Set the saw blade just deep enough to cut through the siding only. Remove the siding. Waterproof the slot with No. 15 building paper.
Read Also: Webbing For Patio Chairs
Pay Attention To Flashing And Roofing Details For A Watertight Job
Building the tie-in framing on top of the existing shingles is a good way to keep the house waterproof as you construct the porch, but when it comes time to install the roofing you’ll have to cut the shingles along each of the valleys with a hook-blade utility knife. Then pry loose the cut shingles to make a wide path for the valley flashing.
Cover the tie-in framing with 3/4-in. plywood. Add blocking as needed and fill in the triangular areas between the existing roof and the new roof.
Design Your Patio Cover
If you have a designing background, you can put together your own designs.
Make sure you put them down on graph paper or use a CADD program to do the designs. This helps keep track of everything and gives you reference material for when the project starts.
Otherwise, make sure you find a reliable engineer that can do the work for you.
The more detailed you can be with your design will not only help you get a permit, but also make building the patio cover a lot easier later on.
It will also help you understand exactly what materials you will need so that you dont overspend on lumber.
Don’t Miss: How To Clean Bird Poop Off Patio
Patio Roof Ceiling Fan Ideas
Youll most likely use your patio when the weather is warmer. Installing a ceiling fan can keep the air circulating and your patio more comfortable. Look for a ceiling fan that is rated for outdoor use and try to balance the size and height of the fan with the size and roof height of your patio.
The ceiling fan you choose should enhance the space. If your patio space is large, youll either want to have a large fan or consider purchasing two smaller models. This will help the sir to circulate throughout the entire patio area.
When choosing a material and design, youll want something that is durable and matches the style of your patio. The most durable material for your fan is stainless steel, but its also the most expensive. For more affordable materials, consider fiberglass, aluminum, or plastic.
Once you know the size and material you need, your next step is to choose a design. A two-blade design will look sleek and modern. For a more traditional design, look for one that has three to five blades.
Install The Ridge And Rafters
Cut the 2×8 roof plates. If you’re not good at calculating roof angles, start by estimating the angles and cutting the plates an extra 6 in. long. Then set them in place, remark the angles and recut them until they fit. Screw the roof plates through the roof boards into the rafters below. Next measure for the ridge, estimate the angle and cut it a little long. Trim the angle to fit and screw the ridge rafter to the first truss and roof plates. Complete the tie-in by installing a pair of rafters. The framing should be exactly 3/4 in. above the top of the trusses.
Also Check: Patio Direct Replacement Slings
Patio Roof Skylight Ideas
If you choose a solid patio roof design, such as timber-framed, wood-paneled, or metal, then youll have a solid roof covering you. While this is excellent at protecting you from the elements, they also block the light. This can make your patio feel dark on even the brightest of sunny days. The answer to this problem is to add a skylight.
You have a lot of freedom in how you choose to add your skylight. You could have several smaller skylights that distribute light evenly throughout your patio. Or you could have one large skylight that allows a lot of light in one spot. When placing your skylights, consider the length and width of your patio and where the main supporting beams are located
It is always better to install a skylight when you build your roof. There is a much greater margin of error when you try to retrofit a skylight. So if you think you might want one, take the plunge and install it when you build your roof.
Install The Joists And Joist Hangers
Nail through the joist hangers into the beams at the house to hold them in place. Then connect the opposite ends of the two beams at the front with a 2×10 cut to the same length as the ledger. Adjust the resulting frame until the diagonal measurements are equal.
Then brace the frame against stakes pounded into the ground to hold it square while you install the treated posts, joists and decking. Sight along the outside rim joist occasionally and adjust the length of the joists as needed to keep the front rim joist straight.
Recommended Reading: How To Paint Wrought Iron Patio Furniture
Apply The Solid/vented Tape And Fasten The Sheets
As soon as you apply the first sheet, you can start fastening it with our specifically designed screws. Start from one corner and work your way along screwing only into the purlins. Not into the rafters. Once fastened the first sheet, you can apply the H profile. In this case we are using a polycarbonate profile that can be easily cut at the proper length of the sheet. Just apply it on the length side of the first sheet and proceed fastening the second polycarbonate multiwall sheet after have added it inside the H profile.
Planning Your Patio Cover
When designing a patio cover, it can help to make a drawing of cover including the house and the patio itself. SketchUp or other designing software can be helpful in your planning, but in lieu of those aids, scale drawings on graph paper will work just fine. For our purposes we will design a cover that is 12 ft. wide by 16 ft. long.
Start by measuring from grade or ground next to the foundation up to the underside of the eaves. Next measure out to the fascia or vertical finish of the eaves. Determining the roof pitch completes this part of the drawing. The simplest way to hold one end of a 2-ft. level against the roof, and then measuring straight down to the roofing material. Divide that number by two and that gives you the pitch, or the amount of vertical rise in the roof per foot of run. Transfer those calculations to your drawing.
Next measure out from the house to the edge of the patio. Most often the grade slope away from the house slightly for drainage. .
Also Check: How To Build A Deck Over A Concrete Patio
Building A Roof Over A Deck Or Patio
Start here if you want to build a roof over a patio or deck. We will walk you through the entire process, from siting the patio roof to raising posts, attaching beams, and installing the roof.
If local codes allow setting the overhead directly on an existing slab but the concrete is not thick enough to support the overheads weight, you will have to pour new footings around the slabs perimeter or break out sections and pour deeper footings. For information on installing a new patio, see Pouring a Concrete Slab.
Most Common Ways To Attach A Patio Roof To An Existing House
Attaching a patio roof entails intermediate carpentry skills and creativity because there are many ways that you can choose from.
All of them have their own advantages and drawbacks. When installed correctly, the patio roof will complement the house and provide an extra entertainment for you and your family for all year round.
Here are 7 different ways of attaching a patio roof to an existing house that you can apply.
Also Check: How To Level Patio Pavers
Staple The Screen To The Walls
The charcoal aluminum screening we used is strong and long-lasting, but you have to handle it carefully to avoid creases and dents. Carefully unroll the screen on a large work surface and cut lengths about 3 in. longer than you need. Reroll each piece and carry it to its location.
Start by tacking the two corners, making sure the screen is square to the opening. Then stretch the screen slightly and staple the sides, top and bottom. Place 1/4-in. staples every 3 in.
Japanese Style Patio Roof
This patio roof conjures up images of Japanese houses. The wooden posts support the exposed beams that overhang a little bit.
The latticework allows natural light to pass through so that you will be covered partially. The lanterns hanging over the green couches accentuate the Japanese style of this patio.
And to make it look like a Japanese traditional house, some bamboos are grown next to and in front of the patio.
Pros:
- The latticework does not completely block the natural light so that it can still pass through the patio roof.
Cons:
- The roof cannot protect you from the rain.
Read Also: Hanging String Lights On Aluminum Patio
Beginning Construction On The Patio Cover
Early the next morning the materials arrived at my house. Once the materials were unloaded, I began carrying the ten-foot-long boards and corrugated metal sheets to the backyard, laying them out in a pattern to roughly match how they would be assembled.
I also separated the corrugated metal sheets, wiped each one down with a light coat of vegetable oil, and then re-stacked them. This was something I had seen a neighbor do a long time ago when I was a child. I dont know if it served any purpose other than making me feel better. Its a step I probably could have skipped, but who was I to doubt the wisdom of the ancients?
Ledger Board Installation
Patio Roof Lighting Ideas
Creating layers of light is the key to creating a lighting scheme for your outdoor space. Strive to have an ambient, accent, and task lighting fixture. Ambient lighting is the generalized light that illuminates the entire space. You can do this by installing overhead lighting. Pendants, chandeliers, ceiling fan lights, and semi-flush/flush-mounted lights. These fixtures will give you a gentle wash of light over your entire patio.
Accent lighting is more decorative and will highlight specific aspects of your patio. This type of lighting is created by installing track lighting, scones, rope lights, string lights, or LEDs. You could use a track light in the ceiling pointed to your outdoor fireplace or you could have lights that point toward your stairs to make them safer at night.
The third type of lighting is task lighting. This is the light youll use in areas where tasks get performed. If your patio roof covers an outdoor kitchen, grill, or bar, youll want to focus this type of light there. The light should remove shadows and make it easier to see what youre doing. Try pendant lighting to focus the light where you need it most.
Don’t Miss: How To Hang String Lights On Aluminum Patio
Choosing The Covered Patio Material
Just because it is an outdoor patio, that does not imply that you need to toss in any unstylish furnishings and options to elevate it. Every decorating decision you are making regarding your covered patio can help add in developing a charming space while having a hint of your style and individuality.
Consider pieces that will help put definitive character within the area while elevating it like on-trend pillows, throws, and printed textiles, which could be quickly switched out for a fast refresh. And do make the most of attractive layered light fixtures which will help jazz up your living area in a covered patio. In reality, you will find that it is not hard to feel ultra comfortable under a covered patio when your outdoor style reflects your taste and personality. Think about having lightweight furniture that matches the scale of your respective covered space.
Before & After Photos
On the left you can see the deck before we stained and painted it followed by the deck before we added the DIY pergola. The photo on the right shows the deck with the finished pergola.
Are you ready for the tutorial? First we had to rip out that arbor. After that we were ready to begin. Here is the complete DIY covered pergola tutorial!
Don’t Miss: How To Clean Porch Cushions
Tips For Purchasing Materials
Different Ways To Join A Patio Roof To An Existing House
Attaching a patio roof to the house is an important decision that requires careful consideration. There are many different ways and positions you can choose from, each with its own pros and cons.
Knowing which position suits your needs best will make attaching the roof easier in the future once you learn how.
Don’t Miss: How Much Is A Concrete Patio