Screen In Porch Under Deck

Screened In Porch Installation Costs

There is no substitute for a genuine lack of planning. To do all you can to make sure everything goes off without a hitch, it is worth paying close attention to the following list and taking action where necessary. On average, a contractor will charge around $300 for installation, not including materials, doors, add-ons, and more.

Construct A Jig To Assemble The Roof Trusses

Prime Before Painting.

Prime and paint the truss parts, wall frame and screen stops before assembly. Prime the wood with a special stain-blocking primer such as Zinsser’s oil-based Cover-Stain. Then brush on a coat of acrylic exterior house paint. Make sure to prime every cut end as you work otherwise, these areas will absorb moisture and cause staining. We prefinished the roof boards with an oil finish .

How to construct the roof truss jig:

It’s easiest to assemble the roof trusses first, using the deck platform as a work surface. Screw two sheets of plywood to the decking and use the dimensions in Figure J to chalk lines indicating the top of the rafters and the bottom of the 2×6 crosstie. Cut triangular blocks and screw them to the plywood to hold the rafters in alignment as you assemble the trusses.

Make A Cushioned Comfortable Couch

Remember what we said earlier about not being stuck with using only outdoor furniture? What if youve already got outdoor furniture that you want to use in your new screened porch? The solution is relatively simple and quite comfortable! You can swap out some oversized indoor cushions for use as outdoor furniture. Adding a coffee table can make this a nice transitional space and function as an outdoor living room!

You May Like: What Does A Pergola Do

Brass Mesh Screen Cost

Being made up of around 70% copper and 30% zinc, brass is referred to as an alloy, and because of the copper content, it acts somewhat similarly to copper in respect to how it will tarnish over time from weathering, called safe corrosion. The darker black and brown appearance is from a normal process called oxidation when it is out in the open. This alloy is better than copper alone because of its ability to resist abrasion and the resulting strength from the combination of the two metals.

However, its not a wise choice for homes near saltwater areas because the salt will cause active corrosion with brass, leaving a green powder or bright, white and green spots often referred to as bronze disease. While it is a stiffer metal than copper, the mesh can still be bent by hand, but unlike copper, it has some spring back whereas copper does not. On average brass mesh screening will cost you $6/sqft.

How To Build A Screened In Porch Under Deck

Screened rooms traditional porch st louis by heartlands how to build a screened in porch under deck mycoffeepot org screened in porch underneath a deck great screened porch under deck houzz underdeck ideas hgtv.

All about screened in porch under deck all about screened in porch under deck screened rooms traditional porch st louis by heartlands underdeck ideas hgtv all about screened in porch under deck two story deck in st louis with screens and underdeck.

Also Check: How To Build A Small Wood Patio Deck

Pay Attention To Flashing And Roofing Details For A Watertight Job

Building the tie-in framing on top of the existing shingles is a good way to keep the house waterproof as you construct the porch, but when it comes time to install the roofing you’ll have to cut the shingles along each of the valleys with a hook-blade utility knife. Then pry loose the cut shingles to make a wide path for the valley flashing.

Cover the tie-in framing with 3/4-in. plywood. Add blocking as needed and fill in the triangular areas between the existing roof and the new roof.

Install The Roof Boards

To bevel the first roof board, set your table saw or circular saw to 23 degrees and rip a bevel on the groove edge of the board. Align the board with the ends of the trusses and nail it with 16d galvanized nails. Install the remaining boards, making sure to snug the joints tight before nailing them. Let the boards hang out past the last truss to form the gable end overhang. Cut the last board on each side to fit at the peak.

When you’re done installing the roof boards, snap a chalk line at the gable end and saw them off to leave an 18-in. overhang. Finish the gable end overhang by installing a pair of rafters and the 1×3 trim. Hold the gable end rafters tight to the underside of the cutoff roof boards and screw through the roof boards to hold the rafters in place. Then cut 1×3 trim to cover the end grain of the roof boards. Extend the trim around the corners and return it along the roof edge to the house.

You May Like: How To Put In A Paver Stone Patio

Staple The Screen To The Walls

The charcoal aluminum screening we used is strong and long-lasting, but you have to handle it carefully to avoid creases and dents. Carefully unroll the screen on a large work surface and cut lengths about 3 in. longer than you need. Reroll each piece and carry it to its location.

Start by tacking the two corners, making sure the screen is square to the opening. Then stretch the screen slightly and staple the sides, top and bottom. Place 1/4-in. staples every 3 in.

Benefits Of Screening In A Porch

Youll not be the first homeowner to immediately recognize a three-season screen porch creates a dry, insect-free outdoor living area where you can still enjoy the outdoors rain or shine. If youve suffered a swollen itchy mosquito bite or a puffy painful bite from a black or horse fly, youll instantly know why a screen-in porch is the way to prevent this agony. There are many benefits of screening in a porch, not the least of which is an increase in value of your home and a place for you to comfortably enjoy the space outside of your home.

Don’t Miss: How To Make A Patio Dog Friendly

Opt For Porch Boards To Protect Against Bugs

If youre building a completely new structure, the ideal option is to avoid using traditional decking altogether. Instead, consider porch boards, which use a tongue-and-groove system that creates a completely solid surface. There are no gaps for bugs to take advantage of, and while screens might eventually rip over time, the porch boards dont have that potential issue. They provide a sturdier and more lasting wood barrier against bugs.

A screen porch should be a safe haven from bugs. If bugs are still finding their way in, taking the time to determine where they are entering is the best first step. The floor is a great place to check, but you might also find gaps in other areas. Once youve identified the issue, an experienced porch and decking professional can help you determine a solution that will keep them out.

How To Set Up An Under Deck Ceiling

For most of these ideas, it is highly recommended, or even required, that you waterproof the ceiling below the deck. Waterproofing the under-deck ceiling is essential for any deck design idea that includes electrical wiring or if you want the under-deck area dry. In addition, waterproofing the under-deck space applies whether you use wood or composite decking. Our guide on under-deck ceiling ideas shows how to set up an under-deck ceiling and a gutter and spout system that will waterproof the decks substructure, keeping your new area nice and dry!

Don’t Miss: Outdoor Fire Pit Covers Round

Add A Deck Screen During Construction

If you are building a new structure using traditional decking, installing the screen is simple. Lay down the screen fabric on top of the joists, and then place the deck board on top to hold it in place. The screen is sandwiched between the bottom of the decking board and the top of the joists, providing an effective barrier. Some systems, like the SCREENEZE screening system, include this.

Screen Porch Under Deck

I am planning on adding a concrete slab under my existing deck in my back yard and building a screen porch on the slab. I am in Minnesota, so the slab will have some movement with frost, but the deck is build on 48 deep footings. Is there a proper way to attach the screen to the deck to allow movement? Thanks,

Recommended Reading: Sam’s Club Pergola Installation

Building Permits And Land Surveying

In most areas, a screened-in porch is considered an addition, and that will require a building permit. These permits can cost anywhere between $447 to $2,313 the national average is $1,380. Small communities may only charge $150, while some cities can charge as much as $7,500.

If your municipality doesnt include land surveying when you apply for a permit, another $200 to $1,000 .

Since the range is so broad, we recommend looking into the cost of applying for a building permit before starting anything.

Build The Deck Square And Level And Assemble The Perimeter Joists

Install the ledger board.

Start by marking the ledger board location on the house wall. We located the top of the ledger board 90 in. below the bottom of the soffit. On our house, this left a 6-in. step down from the patio door to the deck surface. Remove the siding and attach the ledger with 1/2 x 4-in. galvanized lag screws . Make sure it’s perfectly level. If the ledger attaches to concrete, predrill holes and insert lead shield lag screw anchors before installing the lags.

Outline deck frame and set beams.

After you mount the ledger, use stakes and string lines to outline the deck frame according to the dimensions in Figure B and mark the footing locations. A few days before you plan to dig the footings, call 411 to have underground utilities marked in the vicinity of the porch. Your local building department will specify how large and deep the footings should be for your climate and soil conditions. Pour a concrete pad in the bottom of each footing hole after they’ve been inspected. Let the concrete set overnight.

Assemble Frame.

Next, choose the six straightest 2x10s for the perimeter beams. Cut the 2x10s for the two side beams to length and nail the pairs together. Use 16d stainless steel or double-dipped galvanized nails for all of the joist framings and to attach the joist hangers to the ledger board. Rest one end of each side beam in the double joist hangers and prop them up until level with a stack of wood.

You May Like: How To Install Ceiling Fan On Patio

Frame The Walls Accurately For Smooth Assembly

Since the wall framing for this screened in porch is the finished surface, it’s worth taking a little extra time to make the framing material look good. We chose the nicest cedar 2x6s we could find and ripped them into 3-1/2-in. and 1-1/2-in. boards. We did this to create sharp, clean edges .

Cut the studs and crosspieces to length and screw the walls together . We used a power miter saw for clean, square cuts, but a circular saw will work too. Use a crosspiece as a spacer when you’re attaching the studs to the top and bottom plates. Then cut a 10-in. spacer block to position the crosspieces for assembly.

How To Screen In A Porch Patio Or Deck

A screened-in porch is an excellent place to relax, read a book, do a crossword puzzle, or chat with your soulmate all while keeping pesky insects on the other side of the stunning enclosure. A DIY screened-in porch allows refreshing breezes to flutter over you and shades you from harsh sunlight. You can get the same benefits with a DIY screened-in patio assuming the patio was designed with the proper foundation to support your new private insect-free oasis!

Also Check: How Thick Should Patio Concrete Be

A Traditional Screen Patio

During the summer, sometimes you want to spend time outside, but you need a little respite from the weather and the mosquitoes. You can solve two problems at once by building a screened-in porch underneath your deck! With a shady, bug-proof spot under your deck, you can enjoy the outdoors during all months of the year. This patio makes for a cozy sunroom, using indoor furniture to turn the space into a second living room or reading space.

Backyard Plans Under The Deck

• Pin

This post is sponsored by Phantom Screens. Im so thrilled to be working with them on our backyard project!

Summer is in full force in Georgia and the heat has been intense already. We are always looking for ways to cool off and spend time outdoors too. Our backyard is very private and it also has a lot of shade except for just a few hours in the middle of the afternoon.

Ever since I went on the Southern Romance tour with Phantom Screens, I have been dreaming of having a porch like this.

Ours wont be this fancy, but I think we can make it nice under our deck. I was so enthralled by the motorized wall screens on the Southern Romance house.

This house was equipped with vinyl panels as well as screen panels that slid into place. We will only do the screen panels on our porch.

Watching the screens in action really got my attention back then and I filed it away for future.

I think our under deck porch will be perfect for a screen system like this. We will have the best of both worlds.

Im so excited to share with you that Im going to be partnering with Phantom Screens and well be getting remote control screens on two sides of the under deck porch. Its really going to change everything for us in using this backyard. Its not a huge space, around 14×14, but I know we will really enjoy and use it as a screened porch.

Adding stairs was the first step to really enjoying our backyard. Now with the under deck ceiling, its going to look so good out there.

Don’t Miss: What Size Patio Table Should I Get

How To Screen In A Porch

Screening in a porch can be as simple as purchasing large rolls of screening and stapling them to existing porch posts. This will work and you can keep insects away from you, but the odds are youll not win a contest for appearance.

Most new screened porches are built from scratch. The porch may rest on top of an existing patio that can handle the weight or you may have to install a new concrete slab or build a raised platform that becomes the floor of the porch adjacent to your home. Both of these require walls to be built and a roof erected over the top of the new structure. Doing all these tasks to create a new space, as opposed to retrofitting an existing open porch, requires considerable skill, lots of time, and a wide assortment of tools.

Aluminum Mesh Screen Cost

Of the metal screen solutions, aluminum screen is a perfect blend of strength, and its still easy to work with because it is easy to both bend and cut with hand tools. Available in silver, black, and charcoal, it stands up to the elementsresisting corrosion from moisture, oxygen, and salt. It will keep its original color but reflect more light and heat than the other two options, and, as such, will be less effective in reducing heat during the summer months. Also, when compared to fiberglass, its strength as a metal will outperform it by a factor of almost 50%, which makes its initial slightly higher cost of $0.28/sqft a worthwhile investment for the homeowner.

Don’t Miss: Does Home Depot Install Gazebos

Maximize Surplus Space Under Your Deck With A Patio

For many deck owners, the space below the deck is not used because of where its located. Atlanta Decking & Fence owner, Dave Tibbetts, loves to help customers get the most out of their deck, and promote the variety of options homeowners have. Imagine having the ability to barbecue year-round. Or to show off your beautiful new space to your neighbors. By adding under deck porches, you can create a dry, usable outdoor room. From storage to entertaining, the possibilities are endless. Heres how to put this space to good use:

• Enclose and furnish your under deck porch. One of the most popular ways to add useable space is with a screened or open porch. They are a functional way to provide shade outdoors and highly popular with buyers once it comes time to sell. Screened or windowed porches give you more outdoor enjoyment, yet protect you from insects and offer up relaxation and privacy.

• Of course, keeping your under deck porch warm and dry is essential for truly enjoying its benefits. A drainage system in the under deck porchs ceiling is a popular upgrade. It captures water and diverts it to a gutter at the deck beam, leaving the deck or your porch dry. It can last three or four decades because the framing never gets wet. You can convert the space under a second-story deck into a dry spacious patio. The drainage is a great tool when it rains, giving homeowners a space they can use even if its wet outside.