Thursday, March 28, 2024
HomePergolaLean To Pergola With Roof Plans

Lean To Pergola With Roof Plans

Diy Pergola Plans Assembly

Building MODERN wooden DIY lean-to pergola with HOT TUB /patio cover / polycarbonate sheet roof

Measure a 10×10 area making sure it is squared by measuring diagonally in both directions.

Use 12 long 6×6 poles with 2 in the ground with concrete as shown in illustration above. If you are using anchors on the poles use 10 6×6 poles.

Use a level to make sure all the poles are leveled.

Once the poles are set make sure all the poles are the same height, you can use a string level for this. Cut poles if needed to get them level.


The top edges on the pole can be cut for a nicer appearance, illustration above shows the edges cut at a 45 degree.

Use four 12 long 2×6s for the support beams , cut the ends as shown on illustration above.

Install the support beams as shown on illustration above, use clamps to hold the support beams in place, secure with 3 1/2 deck screws.

Use seven 12 long 2×6s for the crossbeams , cut the ends as shown on illustration above.

Lay the crossbeams in place and mark were the 3 notch will go. Secure the crossbeams using 3 1/2 deck screws.


Use eleven 12 long 2×2s for the slats. The ends can be cut for a nicer appearance, illustration above shows end cut at 45 degree. Use 3 1/2 deck screws to secure the slats.

Cut eight 2×6s to 4 4 3/4 for the brace , cut as shown on illustration above.

Install the brace to the pergola using 3 1/2 deck screws as shown on illustration above.

Plans For A Large Wooden Pergola

Pergolas can be small for a swing or aslarge as a deck. You can make it as huge as you want it to be or just as simpleas something to hang your plants on. This is a plan to construct a very largewooden pergola.

This can be a structure placed on your deck,near your pool, as the highlight of your garden or a venue for an event orparty. But no matter what or how you want to use this pergola you will surelylove its wide roof area with plenty of promising styles to create.


A Simple Deck Pergola With Plant Hangers

A pergola is a ersatile outdoor structure.It can be used to beautify your outdoor area and at the same time, serve apurpose. This can be used as a structure to shield plants from direct sunlight.

You can use a supports to hang aerialplants as well. This first pergola DIY plan is a simple one, with basicinstructions on how to construct the pergola lower and upper supports.

Don’t Miss: How Much Is A New Patio

How To Frame A Lean To Roof

Framing a Lean to Roof step by step

lean to roof framing is a kind of free-standing structure. The height of one sidewall is built higher than the other sidewall.


For this framing lean to roof, the upper part of the common rafters is fixed to the wall with a wall plate. The upper end of the lean to rafters are fixed to the wall with a corbel.

These corbels are made of various materials such as stone, brick, or iron. In this type, the lower end of the rafter is attached to the wall with a wooden post-plate. And the rafter is attached to the verandah wall. Iron knee straps and bolts are used to connect the rafters to the post plate.

Normal rafters are fixed by giving a slope so that it stays at 30 degrees along the wall. The maximum length of lean to roof is suitable for a span of 2.5 m.

Preparing The Acrylic Sheets

Lean to box Pergola

Pre-drilling in wood might be important but optional. When it comes to acrylic its a must.

Stack all the sheets on a flat surface making sure all the sides are flush. Now, draw a line alongside, 2 cm away from the edge. Starting from 2 cm away from the end mark points right between the line and the edge. Make a note of the spacing between the points in order to avoid drilling into a screw when putting down the finishing battens. In this case, it was around 20cm.


Now using a metal drill bit, drill and countersink screw holes for mounting screws. Acrylic will crack if you don’t!

Also Check: Can You Use An Outdoor Heater Under A Covered Patio

The Patio & Planter Design

A trellislike pergola is a combination between a pergola and a planter. It has four boxes around the post, which you can use to plant flowers. You can have it ready in two or three weeks, but you wont be able to build it by yourself, so make sure that you have helpers ready.

The provided plans are for a 16 x 20 feet wooden pergola, and you can make it from pressure-treated wood, redwood or cedar. Its a great way to enhance an outdoor space. You could also add on a to really spruce up your backyard aesthetic.

Step : Rafters Purlins Fascia And Brace

  • Cut the rafters to length and angle cut each end to suit. Work out the rafter length to suit the roof sheets if possible . In this example cut the rafters 2280mm long for 2400 roof sheets. Thus ledger 50mm + rafter 2280mm + fascia 20mm + roof overhang 50mm = 2400mm Refer to the plans for reference if necessary.
  • Fix four rows of 100Ã50 nogs on edge in-between the rafters as in the flat plan These are the nogs that the roofing is fixed to.
  • Fix the top row of nogs 100mm down from the top of the rafters and fix the bottom row of nogs 100mm up from the end of the rafters.
  • Fix the other two rows of nogs equal distance apart.
  • Alternatively the purlins can be fixed on top of the rafters if there is enough room between the top of the rafters and the eaves.
  • Fix fascia board along the end of the rafters and also up the sides of the two end rafters .
  • Brace on top of the frame diagonally from corner to corner with metal strap brace. see flat plan.

Recommended Reading: What Is The Best Patio Slab Cleaner


The Arbor Seat Blueprint

This Pergola arbor seat was built to exist in an apple orchard. The builder designed it for his wife who wanted a meditative space for quiet contemplation outside. The instruction plans walk you through how to create the uprights, the latticed backs, the seat back, the sides, the seat base, and the roof. Prospective builders comment that theyve seen similar looking builds at their elderly relatives homes

Lean To Pergola Products For Sale Ebay

14×16 Lean to Gazebo Plans
  • Highest rating: 3
  • Lowest rating: 3
  • Descriptions: Buy lean to pergola products and get the best deals at the lowest prices Lean to Wooden Carport Pergola Canopy | Clear Roof or Frame Only | Wall Fixed.
  • More : Buy lean to pergola products and get the best deals at the lowest prices Lean to Wooden Carport Pergola Canopy | Clear Roof or Frame Only | Wall Fixed.
  • https://www.ebay.co.uk/b/lean-to-pergola/bn_7024952782

You May Like: How To Stamp And Stain Concrete Patio

Gazebos And Carports Vs Pergolas

A related outdoor wooden structure is the gazebo. But gazebos always have a closed roof, which is not true of pergolas. Many gazebos are further distinguished from pergolas by having:

  • A rounded shape

A “carport” is a structure defined more by its purpose than by how it is made. Carports are used to shelter one’s automobile at home in lieu of the more expensive option: a garage. The basic carport is a roof supported by posts. But we have seen more elaborate carports that are essentially pergolas co-opted for car storage.

This One Car Carport Features A Sturdy 66 Framing And A Roof With A : 12 Slope

Lean to pergola roof ideas. See more ideas about house with porch, patio, porch design. Pergola with roof pergola patio backyard patio modern pergola white pergola metal pergola covered pergola lean to roof lean to carport. Roof patio designs pergola attached is one images from 19 cool how to build a lean to roof on a porch of can crusade photos gallery.


Building a porch roof framing roof over patio awesome build deck slanted porch home elements and 50 stylish covered patio ideas 50 stylish covered patio ideas 50 stylish covered patio ideas image result for lean to porch canopy outdoor pergola. A massive 150mm x 150mm are supplied as standard. They measure 2.2m long when cut flat at the bottom.

A 10×12 size measures 10×12 to the outside face of the posts, and has a 12×14 roof span. See more ideas about pergola, carport designs, lean to roof. Build over ft wide to your roof rafter calculator and rated to add value to build the pitch it provides enough room you how to shed heavy rain and has a small addon wall can simplify the most building no and wide leanto roof jeep2001mred loading unsubscribe from jeep2001mred loading is used in feet to be minimum pitch versus.

12×24 attached lean to carport plans. See more ideas about pergola, pergola patio, patio. They come with detailed instructions, diagrams and pictures, including various ways in which they can be adapted to suit your needs and style.

Recommended Reading: Pergola Roof Panels Home Depot

Are You Creating A Flat Roof Pergola Or A Pitched Roof Pergola

When thinking of the pitch, or slope, of a pergola most people tend to envision either flat or a medium pitch, however, every pergola most have a slight pitch to allow for water drainage. Pergolas can actually be created to any angle however, the pergola style tends to be low pitch roof and a minimum 5 degree pitch is considered to be normal best practise

Did you know that the steeper the slope of your pergola the more self cleaning it will naturally be? The steeper the pitch the better the rain and water run off will be which in turn cleans your roof better and reduces the chance of direct/leaves settling on top

Slope roof pergolas or slanted roof pergolas are 10 degrees plus which creates a distinctive silhouette and can be great in complementing the angle on your house. This means pitched roof pergolas tend to be popular for lean to pergolas that are against a house wall or on a back door patio.

In comparison, flat roof pergolas are between 5 to 10 degrees so are the typical choice when you are creating a freestanding pergola in your garden. This is because the flatter slope can look more natural on top of a decking or patio area and be a more subtle natural shape in your garden!

Why Trust The Spruce

TOJA GRID

This article was researched and written by Deanna McCormack, a freelance writer specializing in home and family with expertise in the outdoor category. She lives in Arizona, where she enjoys indoor/outliving and knows the importance of shade and protection in her backyard. She considered dozens of pergola kits for this roundup, evaluating each model on ease of assembly, sturdiness, and design aesthetic.

Don’t Miss: How To Make A Pea Stone Patio

Laying Down Foundation Posts

  • 1Place a post into the first hole. Youll want to use posts that are at least 8 by 8 inches thick and 10 feet long. Work on each post one at a time until it’s secured to the ground. Put one end of the post into a hole and make sure that it rests flat on the gravel. Hold the post in place as you move onto the next steps.
  • Posts shouldn’t go straight into the ground, because you want to minimize wood rot. Pour them in with rapid set quickcrete, or if you’re on a flagstone or paved patio, use brackets that create a gap between the surface and the post. Then the brackets are poured into the concrete, and the posts are bolted into the brackets.XExpert Source
  • Attach The Vertical Closure Strips

    Once all of the horizontal closure strips are installed, add the vertical closure strips.

    If your roof panels will end at the edge of your pergola frame, line the vertical closure strips along the end between the last raised part of the horizontal strips.

    Cut the vertical closure strips to length using tin snips.

    Since my pergola roof extends out beyond the frame, I used the vertical closure strips to secure the edges of the panel to the rafters that stuck out.

    If youre doing this, make sure you only install the vertical closure strips on rafters that line up with the raised part of the horizontal closure strips.

    You May Like: What Is A Commercial Roofer

    Recommended Reading: How Much Is Alumawood Patio Cover

    The Diy Freestanding Garden Blueprint

    This freestanding garden pergola has a 10 x 10 feet base, but the plans allow you to modify it to any size your want. For an 8 x 8 wooden pergola, the beams and crossbeams will be 10 feet, while for a larger the beams will measure 14 feet. There is a handy pergola building guide and detailed schematics so that it wont be difficult even for an amateur to build this garden structure.

    How Do You Slope A Pergola

    How to Build a Pergola Attached to Your House | Mitre 10 Easy As DIY

    Is there such a thing as how do you slope a pergola? Pergolas are, by far, the most popular type of pergola.

    If you are remodeling or building a new home, or even if you are building a new home, then the chances are good that you will need a pergola or perhaps, a patio in some form.

    As with any type of structure, there are always factors that you need to consider before getting the installation of a new pergola. One of those factors is how you slope your pergola. Not only is it a simple task but it is also quite important.

    Firstly, there are some factors to consider when you are looking at the slope of the pergola. These factors will depend upon the size of the pergola and the design of the building. So, these factors will depend upon the building that you are installing a pergola in.

    However, before you are concerned about the slope of your pergola, you need to be aware of what goes into planning the construction of the structure.

    First of all, you should consider your use of the pergola. After all, you will want to make sure that you are making the best use of the structure. This is because it will be used in many different environments.

    Secondly, you should consider the weather of the area that you live in. Also, you should plan for the weather that you expect in the future.

    Therefore, the slope of the pergola needs to be based on the type of weather that you expect to see in the future.

    You May Like: What Is A Grill Gazebo

    Can I Really Build This Pergola Myself

    Of course!

    Even though the finished pergola looks stunning, it is actually quite straightforward to build once you know what size fixings to use and where to cut the notches. Just follow the plans and you will have this wonderful pergola installed in no time at all.

    And you will be able to build it for around about £160, with all the timber and fixings included.

    The beauty of building a DIY pergola is that you can modify it so that it exactly suits you taste, style and situation at a fraction of the cost for someone else to come and build it for you. Even if you buy a pergola kit, you will pay more, have less control over the design details, and will have to install it yourself.

    So if you feel confident, have a go. It’s a great feeling, making a pergola from scratch. And the end result is well worth it!

    Fancy a wooden swing seat like the one in the picture? They are not easy to come by, but this one is ready-made and good to go…

    These particular plans were originally created for someone who wanted to build a specific pergola design for their garden, so they form part of the ‘Additional Pergola Plans Series’.

    Of course, you can use the principles outlined in the free pergola plans to build any pergola or arbour.

    £12.97

    What Roof Glazing Colour

    In essence the colour of the sheets that your use on your lean to pergola roof are determined on the type of glazing you go for. However, with Axiome Multiwall Polycarbonate Sheets and Axgard Solid Glazing Sheets there are three main colour options that you can have on your pergola

  • Clear Pergola Roof – High light transmission and maximum sunshine!
  • Opal Pergola Roof – Reduces heat build-up, nice cool glow, and bright overall appearance
  • Bronze Pergola Roof – Reduces Sun Glare, retains heat and nice aesthetic when creating a wooden pergola
  • An alternative glazing option when creating pergola with a polycarbonate roof is our Axgard® Patterned Sheets which have a high light transmission but create privacy and a glass like effect.

    Recommended Reading: Wood Fire Pit Table Top

    Lean To Pavilion Roof Plans

    Building-a-12×16-lean-to-pavilion

    • E 10 pieces of 2×6 lumber 173 long RAFTERS
    • F 6 pieces of 1/2 plywood 48×96 long, 3 pieces 24×48 long, 2 pieces 29×96 long, 1 piece 24×29 long ROOF SHEETS
    • G 4 pieces of 1×8 lumber 108 long, 2 pieces 78 1/2 long, 2 pieces 96 long TRIMS
    • H 275 sq ft of tar paper, 275 sq ft of asphalt shingles ROOFING
    • 10 pieces of 2×6 lumber 16 ft
    • 9 pieces of 1/2 plywood 4×8
    • 4 pieces of 1×8 lumber 8 ft
    • 4 pieces of 1×8 lumber 10 ft
    • 275 sq ft of tar paper, 275 sq ft of asphalt shingles
    • PART 2: 12×16 Lean to Pavilion Roof Plans

    The Plant Deck Hangers Build

    Pollitt Lean Pergola

    The Lowes deck pergola with plant hangers is a heavily customizable option that has a modern appeal with its exposed bolts and cables. Its identified as an advanced skill level plan that takes one weekend to build and will cost under $500 in total.

    Youll need to have a couple of tools handy including a circular or compound miter saw, drill and bit set, as well as some treated lumber. The image shows a pergola designed to fit a 12 x 14 deck but Lowes instructions help you to customize it to fit your property.

    They advise woodworkers to contact a local utility company to ensure that when you dig the post footings that you dont intercept any buried lines and pipes.

    Since youll be working with pressure-treated lumber, they also advise that you take some safety precautions including wearing a dust mask and goggles to avoid exposure to unhealthy chemicals. Indeed, this is a particularly professional and attractive looking option.

    Don’t Miss: Can A Propane Patio Heater Be Used In A Garage


    RELATED ARTICLES

    Most Popular